Grandstream GDS37x0 In-Wall Mounting Kit in Africa
Create a cleaner, more integrated entrance installation for compatible Grandstream GDS door systems. This purpose-built recessed mounting solution helps installers place supported access-control hardware within a prepared wall opening instead of leaving the complete device standing proud of the surface. FourTeck supports business buyers, contractors and system integrators with model verification, installation planning, accessory matching, regional delivery coordination and quote assistance.
Request QuoteCheck Africa Availability
Quick Product Information
Grandstream
GDS37x0-INWALL / GDS-WMK
Recessed in-wall mounting accessory
GDS3710 and GDS3705; verify other variants
Solid wall, stud wall and drywall / hollow wall
Approximately 99.8 × 193.88 × 35 mm; confirm guide
Bottom edge around 50–55 inches above floor level
Supplier and destination dependent
Compatibility, quote, delivery and warranty guidance
Qualified installer following local building and electrical codes
Product Overview
A door-entry station is one of the most visible parts of a physical security system. It may be installed at a reception entrance, staff gate, loading area, apartment lobby, restricted room or perimeter access point. Although buyers often concentrate on the electronic device, camera, keypad, RFID reader or network connection, the mounting method has a major influence on the finished appearance, physical stability, cable routing and future serviceability of the installation. The Grandstream recessed mounting accessory addresses that practical part of the project by providing a structured way to position a compatible GDS device within the wall.
Surface mounting can be appropriate where construction work must be minimal or where the building cannot be cut. In locations where a more integrated finish is preferred, however, a flush installation may offer a cleaner profile. The door station sits closer to the wall plane, reducing projection and helping the entrance look deliberately designed rather than added as an afterthought. This can matter in hotels, executive offices, residential developments, hospitals, education facilities and commercial buildings where security equipment must blend with architectural finishes.
The kit is not an electronic controller and does not replace the GDS door station itself. It is a mechanical installation accessory. Buyers therefore need to treat it as one component in a wider access-control package that may also include the compatible door station, network cabling, PoE switching or injection, door strike or magnetic lock hardware, exit devices, power arrangements, protective accessories and configuration services. Correct planning prevents the common situation in which the main device arrives but the installer cannot complete a professional recess because the required box, frame, security fasteners or wall dimensions were not confirmed.
Grandstream’s accessory information identifies primary use with the GDS3710 and GDS3705. Distribution channels may use several naming formats, including GDS37x0-INWALL, GDS37XX-WMK and GDS-WMK. Those references can create confusion because similar names may be used across older and newer door-station families. FourTeck recommends confirming the label on the access device, the required mounting accessory part number, the wall construction and the installation drawing before a purchase order is finalized. This small verification step is especially important for project quantities, where a mismatch can delay multiple entrance points at once.
For Africa projects, FourTeck can assist procurement teams, security contractors and systems integrators with this verification process. Support can include reviewing the intended GDS model, checking the stated wall opening, identifying related accessories, preparing a quantity-based quotation and coordinating delivery requirements. The goal is to help the buyer receive an installation package suited to the building and deployment plan, rather than selecting only by a shortened product title.
Key Business Benefits
A mounting kit may appear simple, but its value is measured in installation quality, project consistency and reduced correction work. The following benefits explain why the correct accessory should be considered during design and procurement, not after the door station has already reached site.
◆ Cleaner Architectural Finish
Recessing a supported door station helps reduce how far the device projects from the wall. This creates a deliberate, integrated appearance at entrances where visitors, staff and residents see the access equipment every day. A consistent flush finish can be especially valuable across multiple doors in a new office, hospitality property or residential development.
✓ Better Physical Stability
A purpose-designed box and frame give the installer a defined support structure instead of relying on improvised brackets or site-made plates. Correct mechanical support helps keep the device aligned and reduces the risk of movement caused by repeated button presses, cleaning, minor impacts or cable tension behind the unit.
⚙ Planned Cable Management
Preparing the wall cavity around a known mounting box gives the contractor a clearer path for Ethernet, lock-control and related cabling. This supports cleaner termination and reduces last-minute drilling around a finished entrance. Good cable planning also makes future inspection and maintenance less disruptive.
● Reduced Rework Risk
When the correct kit is ordered before wall finishing, builders can form the opening to the specified dimensions and coordinate it with cabling. That can help avoid enlarging an opening, adding trim plates, repairing plaster or rescheduling trades after the main security device is delivered.
🔒 More Controlled Fastening
The accessory package commonly includes purpose-matched mounting and anti-tamper hardware. Using the intended fasteners helps the installer secure the assembly without substituting unsuitable screws that may affect fit, appearance or later service access. Final security still depends on correct installation and the surrounding wall structure.
↗ Consistency Across Projects
Organizations deploying several access points can standardize cut-outs, mounting height and finishing details. This assists contractors, facilities teams and maintenance personnel because each entrance follows a repeatable arrangement instead of using different site-built solutions.
✓ Easier Procurement Coordination
Including the mounting kit on the bill of materials allows the buyer to review the complete installation package. It becomes easier to align quantities, delivery dates, wall preparation and installer responsibilities, particularly when projects involve multiple branches or phased building work.
Product Highlights
Designed to place a supported Grandstream GDS unit within the wall instead of relying on the standard surface position.
Supports planning for solid masonry, stud construction and drywall or hollow-wall environments, subject to appropriate preparation and local codes.
Published channel documentation commonly references an opening around 99.8 mm wide, 193.88 mm high and 35 mm deep. Always use the guide supplied with the selected kit.
Typical packages include an in-wall box, metal frame, cover plate, drill template, mounting hardware and anti-tamper fasteners. Confirm the exact package contents at quotation.
The strongest feature is not a complicated electronic function; it is the ability to organize the physical installation around a known accessory. The box creates the recess, the frame supports alignment and the cover arrangement provides the finished edge around the door station. This reduces dependence on improvised metalwork, which may vary in quality from one entrance to another and can complicate warranty discussions if the device is damaged by unsuitable mounting.
A recommended lower edge height of approximately 50 to 55 inches above floor level is commonly stated for the GDS37x0 installation. That recommendation helps position the camera, microphone, speaker, keypad and reader area for typical users, but it should not replace an accessibility review. Building type, local regulation, wheelchair access, expected user height, entrance slope and camera field of view can require an adjusted final position.
The kit does not provide weather sealing by itself, does not add network connectivity and does not supply power. Outdoor suitability depends on the compatible door station, correct wall sealing, cable entry protection, drainage considerations and the quality of workmanship. Buyers should treat the accessory as part of a complete installation method rather than as a universal enclosure.
Technical Specifications
| Specification | Details | Buyer Note |
|---|---|---|
| Brand | Grandstream | Match the accessory to the exact Grandstream device label. |
| Model References | GDS37x0-INWALL, GDS37XX-WMK or GDS-WMK | Naming may differ by channel; confirm manufacturer part number. |
| Accessory Type | In-wall recess and flush-mount kit | Door station is normally sold separately. |
| Primary Supported Models | GDS3710 and GDS3705 | Verify GDS3702, GDS3712 or any other variant before ordering. |
| Wall Types | Solid wall, stud wall and drywall / hollow wall | Fixings and preparation must suit the wall material. |
| Approximate Recess Space | 99.8 × 193.88 × 35 mm | Use the supplied drill template and current guide as final authority. |
| Suggested Position | Bottom edge approximately 50–55 inches above floor | Review accessibility, camera angle and local requirements. |
| Typical Components | Plastic in-wall box, metal frame, cover plate, drill template and fasteners | Package contents can vary; verify at quote stage. |
| Power Requirement | None for the mounting kit | The installed door station has separate power and network requirements. |
| Network Connectivity | Not applicable to the mechanical accessory | Plan cable routes before closing the wall. |
| Finish | Designed to complement compatible GDS hardware | Confirm colour and visible trim for architectural approval. |
| Installation | Professional installation recommended | Follow local building, electrical and accessibility codes. |
| Warranty | Supplier and region dependent | Request written warranty guidance with the quotation. |
| Africa Availability | Configuration, quantity, supplier and destination dependent | Contact FourTeck for current sourcing and delivery coordination. |
How to Use These Specifications
Dimensions and model references are valuable for early planning, but the installation template supplied with the exact accessory should control the final cut-out. Product revisions, packaging changes or regional part-number differences may affect the hardware supplied. Before any wall is cut, compare the kit, the door station and the current quick installation guide. For large projects, approving one sample installation before repeating the cut-out across every entrance can reduce risk and give the architect, security consultant and facilities team an opportunity to confirm appearance and user height.
Configuration and Buyer Guidance
The correct purchase decision begins with the installed door station, not the wall alone. Record the full model from the product label or approved bill of materials and confirm whether the project uses the GDS3710, GDS3705 or another member of the family. Avoid relying only on a description such as Grandstream intercom bracket because several accessories can sound similar while having different physical dimensions.
1. Confirm the Device
Share the exact GDS model, product label photo and quantity. Where the project specification uses an older name, ask FourTeck to cross-check the current accessory reference.
2. Identify Wall Construction
State whether the entrance is concrete, blockwork, timber or metal stud, gypsum board, cladding or another finish. The mounting method and anchors must match the substrate behind the visible surface.
3. Review Available Depth
Check the wall cavity, reinforcement, conduits and structural elements. A nominal 35 mm recess cannot be assumed where columns, steel, pipes or existing cables occupy the intended location.
4. Plan Cable Entry
Determine how Ethernet, lock control, alarm input, exit button and power-related wiring will enter the box. Include service slack without forcing cable bends against the back of the device.
5. Check Outdoor Detailing
For exposed entrances, review sealing, drainage, rain direction, sun exposure and wall finish. The recess kit does not replace suitable weatherproofing practice around the installed door station.
6. Coordinate the Trades
Security, networking, electrical and building contractors should agree who forms the opening, installs the box, pulls cable, mounts the device, seals the wall and completes final testing.
The buyer should also decide whether installation consumables are part of the accessory package or supplied locally. Anchors suitable for one wall may not be correct for another. Where the building has decorative stone, metal panels, glass surrounds or fire-rated partitions, consult the relevant contractor before cutting. Fire stopping and rated-wall integrity may require approved materials and methods beyond the mounting kit itself.
Ideal Business Use Cases
The accessory is most useful where the project values a controlled, recessed entrance finish and can prepare the wall before final decoration. It is not limited to one industry. The practical requirement is a compatible Grandstream door station, suitable wall construction and an installation team able to follow the product guide.
Corporate Offices
Reception entrances, executive areas, staff-only doors and meeting-floor access points benefit from a tidy installation that complements modern office finishes. Standardizing the recess across several doors can simplify handover documentation and future maintenance.
Residential Developments
Apartment blocks, gated communities and managed residences often require door stations at prominent visitor entrances. A flush arrangement can reduce visual bulk while supporting a consistent look across blocks, gates or lobby access points.
Hotels and Hospitality
Guest entrances, staff access doors, service corridors and restricted operational areas need equipment that is secure but visually considered. Early coordination with interior and façade teams helps the mounting kit blend into the design.
Education Campuses
Schools, colleges and training centres may deploy access devices at administration buildings, laboratories, residence halls and staff areas. The structured mounting method supports repeatable positioning and can reduce exposed edges in busy circulation zones.
Healthcare Facilities
Clinics, hospitals and laboratories may use controlled doors for pharmacies, records, staff zones and technical rooms. A neatly integrated mounting arrangement can support cleaning routines and professional facility presentation, subject to hygiene and wall-finish requirements.
Warehouses and Logistics
Administrative entrances, secure cages, dispatch offices and high-value storage areas can use the kit where walls permit a recess. Installation teams should account for vibration, vehicle movement, protective barriers and the possibility of impact near operational doors.
Retail and Mixed-Use Sites
Back-office doors, delivery entrances, management areas and mixed-use lobbies may require controlled access without an oversized surface assembly. The mounting accessory helps align the door station with storefront, lobby or service-corridor finishes.
Government and Institutional Buildings
Public-sector offices and institutional facilities often require documented, repeatable installation standards. Confirming the accessory and cut-out during design assists tender preparation, contractor coordination and acceptance testing.
In retrofit projects, the use case depends on what already exists inside the wall. A flush arrangement may be less suitable where cutting is restricted, asbestos or hazardous materials are suspected, historical finishes must be preserved, or structural elements prevent the required depth. In those situations, a compatible surface-mount approach may be more practical. FourTeck can help buyers compare the intended finish and accessory requirement before the site commits to wall work.
Grandstream GDS37x0-INWALL Flush-Mount Integration
The core feature of the kit is controlled integration with the wall. A surface-mounted device is attached on top of the finished plane, while a recessed installation creates a cavity so much of the mounting structure sits behind that plane. The visible door station therefore appears closer to the wall and the trim can cover the transition between the device and the prepared opening.
For business buyers, this difference is more than decorative. Recess planning establishes where the cable enters, how the unit is supported and what space is available behind the device. It can also reduce the chance of the door station being caught by bags, equipment or passing traffic because there is less projection. That does not make the installation impact-proof; the surrounding wall, fastening and site conditions still determine physical resilience.
The quality of the finished result depends on accurate setting out. The opening must be level, the box must not twist, and the visible frame should meet the wall finish evenly. If plaster, tile, stone or cladding is added after the box is positioned, the builder must account for final thickness so the door station does not end up too deep or too proud. A sample installation is valuable where many identical entrances are planned.
Maintenance access should remain part of the design. The kit is intended to secure the device, but authorized technicians still need to remove it for cable inspection, firmware-related troubleshooting or replacement. Do not bury fasteners under sealant or decorative trim that cannot be removed without damaging the wall. A professional finish should support both daily appearance and responsible lifecycle service.
Grandstream GDS37x0-INWALL Multi-Surface Installation
Support for solid wall, stud construction and drywall gives project teams flexibility, but each surface requires a different installation approach. In masonry, the installer may need controlled cutting, dust management, suitable anchors and protection against cracking around the opening. The box should be positioned without weakening structural elements or damaging concealed services. Water paths in external masonry also need consideration.
In a stud wall, the opening must be coordinated with the framing. The cavity may be deep enough, but a stud can occupy the exact intended position. The contractor may need approved noggins or additional support so the mounting box is not held only by a thin board. Where the partition has fire, acoustic or security performance requirements, any modification must maintain that rating through approved construction practice.
Drywall or hollow-wall installation requires careful load distribution. The face board alone should not be assumed to support repeated user interaction or attempted tampering. The supplied hardware must be used appropriately, and the installer should assess whether backing support is necessary. Edges of the cut-out should be clean and protected so the finish does not crumble during tightening or future device removal.
Decorative finishes introduce another layer. Tile needs accurate cutting to avoid fractures; stone may require specialist tools; metal cladding can have sharp edges and grounding considerations; timber panels can move with humidity. The visible trim dimension should be checked against the opening so there is adequate overlap without hiding an oversized or irregular cut.
This multi-surface capability is useful because businesses do not have one standard building type across Africa. A single organization may operate from concrete offices, lightweight branch partitions and renovated retail spaces. The accessory provides a common mounting concept, while qualified local installers adapt the fixings and preparation to each building condition.
Grandstream GDS37x0-INWALL Installation Security and Serviceability
Entry equipment must remain secure against unauthorized removal, but it must also be serviceable by approved personnel. The mounting package commonly includes anti-tamper screws and the matching tool, helping the installer use fasteners designed for the assembly rather than ordinary screws that are easy to remove. These components contribute to controlled access to the hardware, although they are only one part of the physical security design.
The wall itself must provide sufficient support. A strong anti-tamper screw cannot compensate for a loose box, damaged board or weak anchor. Installers should tighten hardware evenly, avoid distorting the frame and verify that the device sits correctly before final acceptance. Where vandalism risk is high, the security consultant may also recommend protective site measures, improved lighting, camera coverage or controlled approach zones.
Serviceability begins with cable organization. Conductors should be labelled, terminated correctly and left with enough controlled slack for the unit to be withdrawn without pulling connections. Excess cable should not be crushed behind the device. Photographs of the open cavity, cable route and final terminations can be added to project handover records so future technicians understand what lies behind the wall.
The anti-tamper tool should be handed to the facilities or security team and stored with other system keys, not left at the entrance. Replacement hardware should match the original specification. If the door station is removed for maintenance, inspect seals, frame alignment and cable condition before reinstalling it. This routine protects the quality of the recess over the life of the system.
For buyers, the practical advantage is a mounting solution that considers both the day-one installation and future authorized access. That reduces the temptation to use permanent adhesives or improvised trim that may look acceptable initially but creates expensive repair work when the electronic device eventually requires attention.
What Buyers Should Check Before Purchase
Before requesting a quotation, buyers should confirm the requirement in enough detail to prevent a model mismatch, missing accessory or unsuitable wall preparation. The following checklist is especially valuable for contractors ordering several units or procurement teams purchasing on behalf of a remote project site.
Exact Model Selection
Provide the full GDS model and, where possible, a clear photograph of the label. Confirm whether the order is for a new installation or an accessory for equipment already on site.
Part-Number Alignment
Check whether the project documentation lists GDS37x0-INWALL, GDS37XX-WMK or GDS-WMK. Ask FourTeck to verify that the proposed item matches the intended door station.
Wall and Finish Details
State the substrate and visible finish, including concrete, block, drywall, tile, stone, timber or metal cladding. Mention wall thickness and any fire-rating requirements.
Opening and Depth
Confirm that the site can provide the required recess without conflicting with reinforcement, studs, pipes, ducts or electrical services. Do not cut from an online dimension alone.
Required Add-ons
Review whether the project also needs the GDS door station, PoE source, rain protection, interface board, RFID credentials, locking hardware, cabling or installation services.
Environment and Exposure
Explain whether the entrance is indoors, sheltered or exposed. Include rain direction, dust, coastal conditions, direct sun, cleaning methods and vandalism risk where relevant.
Quantity and Project Phasing
Share the total quantity, required delivery date and whether units are needed in one shipment or phases. A pilot unit may be sensible before a large rollout.
Warranty Expectations
Request written guidance on accessory warranty, handling damage, installation exclusions and the process for reporting a defective or incomplete package.
Delivery Destination
Provide country, city, site type and receiving contact. Remote or controlled sites may need special delivery coordination, documentation or consolidated shipment planning.
Installation Responsibility
Clarify who will prepare the opening, install the box, terminate cables, mount the device, seal the wall and complete functional testing.
Alternative Mounting Plan
Where recessing is impossible, ask about a compatible surface option rather than modifying the in-wall kit or forcing it into an unsuitable cavity.
Information for the Quote
Send the model, quantity, wall type, delivery location, required accessories and target schedule. This gives FourTeck enough context to prepare a more useful proposal.
Long-term usage cost is usually driven less by the price of the bracket than by labour and wall finishing. A low-cost but incorrect accessory can create rework that exceeds the value of the kit. Buyers should therefore compare total installed suitability: correct fit, available cavity, included hardware, installer capability and future access. For projects with several similar entrance devices, ask whether one approved sample can be supplied first. The sample can confirm the cut-out, trim overlap and final visual result before the construction team repeats the detail across the site.
Africa Availability and Service Support
FourTeck supports product enquiries across Africa with assistance for accessory selection, model matching, quotation requests, order coordination and warranty guidance. Availability can vary because this is a specific installation component and supplier holdings may change according to region, production cycle and demand. Project buyers should avoid assuming that a door station and its in-wall accessory will have the same lead time.
For a useful availability check, provide the Grandstream device model, desired mounting-kit quantity, delivery destination and required date. If the order supports a new access-control deployment, include the quantities of door stations and related accessories so FourTeck can review whether the bill of materials is balanced. This can help identify simple gaps, such as ordering ten door stations but only eight mounting kits, or specifying an in-wall accessory for a location where a surface mount is required.
Delivery coordination can include guidance on consolidated shipping, project phasing and documentation, subject to the final quote and destination. FourTeck can also discuss suitable alternatives when the requested part is unavailable or does not match the installed model. Any alternative should be confirmed technically before wall preparation begins.
Warranty handling depends on supplier terms, product condition and installation circumstances. Keep packaging, part labels and photographs until the installer confirms that the kit is complete and undamaged. Report missing hardware or visible defects before installation. Damage caused by incorrect cutting, unsuitable anchors, over-tightening, exposure or unauthorized modification may not be treated as a manufacturing issue.
Africa Country and Regional Coverage
Businesses and project teams across Africa, including Kenya, Uganda, Nigeria, Ghana, Tanzania, Rwanda, Ethiopia, South Africa, Zambia, Botswana, Senegal and nearby regional markets, can contact FourTeck for availability checks, compatibility guidance and quotation support. The purchasing process can be adapted for a single replacement accessory, a new office entrance or a multi-site access-control rollout.
Regional conditions differ. Wall construction, outdoor exposure, local codes, import requirements, delivery routes and installer capability may affect the most suitable arrangement. Buyers should share site information rather than assuming one installation detail will work everywhere. For multi-country projects, FourTeck can help organize a consistent product reference while the local contractor confirms wall preparation and compliance in each destination.
Useful regional resources include the FourTeck Africa technology platform, the FourTeck Kenya site and the FourTeck Uganda site. Contact the sales team with the exact model and destination for current guidance.
GCC, Middle East and Africa Availability
FourTeck Africa can support enquiries for businesses across Africa while selected FourTeck platforms also assist technology requirements connected with GCC and Middle East markets. This can be useful for organizations whose procurement team is based in one region while the installation site is located in another, or for integrators managing a common Grandstream access-control standard across several offices.
Requests associated with the UAE, Saudi Arabia, Qatar, Oman or Bahrain should include the installation destination, quantity and required schedule. Availability, delivery methods, tax treatment, warranty handling and documentation may differ from one country to another. A product reference that is common in one market may be listed under another channel code elsewhere, making part-number confirmation particularly important.
For cross-regional projects, prepare one schedule showing the door-station model, mounting method, site quantity and wall type for each location. FourTeck can use that information to help identify whether the same kit is appropriate across all sites or whether some entrances need a different approach. The local installer remains responsible for code compliance, structural suitability and final workmanship.
Visit FourTeck UAE for relevant regional technology enquiries or use the Africa contact channel for projects centered on the continent. Final supply terms are confirmed through the quotation process.
Other Options Buyers May Consider
A mounting accessory is normally purchased as part of a wider door-entry solution. The following related items help buyers think through the complete requirement. Availability and compatibility should be confirmed for the exact project; these cards are not a substitute for a technical bill of materials.
Grandstream GDS3710
A compatible HD IP video door system for projects requiring video, intercom and access functions. Confirm device availability and the correct mounting accessory together.
Grandstream GDS3705
An audio-focused IP door access device listed by Grandstream for use with the in-wall kit. Verify the exact project feature requirement before selection.
Grandstream GDS Accessories
Related items can include rain covers, RFID credentials, interface accessories and mounting components. Choose only items supported by the selected device.
PoE Network Equipment
The mechanical kit needs no power, but the installed door station may rely on compatible PoE infrastructure. Check power budget, cabling and network design.
Access-Control Hardware
Locks, exit buttons, power supplies and door interfaces should be selected according to the door, safety requirements and system design.
Surface-Mount Alternatives
Where cutting the wall is not permitted or the cavity is unsuitable, ask about the standard mounting arrangement or a supported alternative for the selected model.
The most useful comparison is not simply one accessory against another. Buyers should compare the complete installed approach: compatible door station, mounting method, wall preparation, power and network, locking hardware, credentials, weather protection, commissioning and future support. FourTeck can help organize related product requests into a single discussion so missing components are identified before shipment.
Why Buyers Choose FourTeck
Business technology procurement is easier when the supplier understands that a small accessory can affect an entire installation schedule. FourTeck approaches the request as part of the access-control project rather than treating the item only as a generic bracket. That means buyers can ask practical questions about model fit, wall preparation, quantity alignment and related components before committing to an order.
Assistance for single-site replacements, new installations, contractor requirements and larger project quantities.
Review of the intended GDS model, accessory reference and related infrastructure to reduce selection errors.
A structured quote process based on quantity, destination, project schedule and requested accessories.
Guidance for regional shipment planning, project phasing and destination information, subject to final terms.
Help understanding supplier warranty terms, reporting requirements and the importance of inspection before installation.
Support identifying compatible door stations, PoE equipment, credentials and other project components where required.
FourTeck does not replace the role of the architect, security consultant or qualified installer. Instead, the team helps procurement move from a vague accessory request to a more complete purchasing requirement. Buyers receive the greatest value when they share accurate information: device model, wall type, quantity, delivery location and target date. This creates a clearer basis for sourcing and reduces the chance of a preventable mismatch.
Frequently Asked Questions
What is the Grandstream GDS in-wall kit used for?
It provides the box, frame and mounting hardware needed to recess a compatible Grandstream GDS door station into a prepared wall opening. The resulting installation sits closer to the wall surface than a standard surface mount. The kit is mechanical and does not include the electronic door station, network connection, PoE source, locking hardware or system configuration.
Which Grandstream models are compatible?
Grandstream’s current accessory page identifies the GDS3710 and GDS3705 as primary compatible models. Some channel listings also reference the GDS3702 and GDS3712. Because naming varies between GDS37x0-INWALL, GDS37XX-WMK and GDS-WMK, buyers should provide the exact device model and request confirmation before ordering or cutting the wall.
Can it be installed in concrete and drywall?
The accessory is intended for solid walls, stud construction and drywall or hollow walls. The preparation and fastening method must suit the substrate. Concrete may require controlled cutting and masonry anchors, while drywall may require backing support. A qualified installer should inspect the site, avoid concealed services and follow local building, electrical, fire and accessibility requirements.
What wall opening is required?
Published product information commonly references an in-wall space of approximately 99.8 mm by 193.88 mm with 35 mm depth. Treat those figures as planning guidance only. The drill template and quick installation guide supplied with the exact kit should control the final opening, especially where tile, stone, cladding or thick plaster affects the finished wall plane.
Does the kit include the GDS door station?
No. The mounting kit is normally supplied as an accessory and the compatible Grandstream GDS door station is purchased separately. Confirm the quotation line items carefully. A complete project may also require PoE networking, cabling, a lock or strike, exit hardware, credentials, weather accessories and installation services depending on the design.
Is the mounting kit available across Africa?
FourTeck supports enquiries across Africa, but current availability depends on supplier status, quantity, destination and product reference. Share the model, required number of kits, delivery country and target date for a useful check. Do not assume the accessory has the same lead time as the electronic door station, especially for multi-site projects.
Can FourTeck help confirm compatibility?
Yes. Provide the full model number, a label photograph if available, the project quantity and the accessory reference shown in your specification. FourTeck can help review these details before preparing the quote. Final installation compatibility should also be checked against the current manufacturer guide and verified by the responsible contractor on site.
What should I provide when requesting a quote?
Include the Grandstream device model, mounting-kit quantity, wall type, installation environment, delivery destination and required date. Mention any related items such as door stations, rain covers, PoE switches, credentials or lock hardware. For a large rollout, state whether delivery is required in one shipment or phases and whether a sample unit is needed first.
Can businesses request bulk or project supply?
Yes. Contractors, integrators, developers and enterprise procurement teams can request project quantities. Supply planning is improved when the buyer shares a door schedule or quantity list showing each site and mounting method. FourTeck can then discuss availability, phased delivery and related product requirements. Final quantities, lead times and commercial terms are confirmed in the quotation.
What warranty guidance is available?
Warranty terms depend on the supplier and destination. Inspect the kit before installation and keep packaging, labels and photographs until completeness is confirmed. Report missing or damaged components promptly. Installation damage, unsuitable fixings, incorrect wall cutting, excessive tightening or unauthorized modification may fall outside product warranty, so qualified workmanship and documentation are important.
Need Help Choosing the Correct Mounting Kit?
Send FourTeck the exact Grandstream GDS model, project quantity, wall type and delivery location. The team can help review compatibility, related accessories, sourcing options and regional delivery requirements before you place the order.
Reviews
There are no reviews yet.